If you can’t get your car started, there are numerous causes this is occurring. One likelihood is that your ignition switch is malfunctioning. A worn-out ignition can be dangerous, so don’t put off getting it looked at by a professional. Examine your automobile carefully. In some instances, you can find the nature of the problem yourself.

Are You Having Trouble Starting Your Vehicle?

When you fire up the engine, the ignition coil pulls its power from the battery, sending it to the sparkplugs, which ignites the fuel so that your car will run. If you turn the engine over too many times, then you’ll probably drain the battery. If that’s what you did, then there’s no power left to start it up again.
Be on the Lookout for these Warning Signs:

•    while idling, you’re often prone to stalling
•    you can’t get your key in the ignition at all
•    you may notice higher auto emissions
•    your key comes out, even while the car’s still running
•    sometimes, the steering wheel sticks, or it actually becomes immovable
•    you may observe increased fuel consumption
•    you might see car battery problems
Reasons for Ignition Issues

Your transponder key isn’t communicating properly. This likely means its computer chip has lost its programming. You can reprogram your existing key; or, you can hire a locksmith professional to copy the existing cuts and program a totally new one. A topnotch expert automotive locksmith technician will know how to carry out the precise, exacting work necessary for this service.

Your ignition has been faulty since the beginning. Consult your manufacturer. If your car’s still under warranty, the dealership ought to replace the ignition cylinder at no charge. If it’s not under warranty any longer, it’s time to call an automotive locksmith.

Your ignition’s set of wafers, which index with corresponding key cuts, are worn out, or jammed up with grime, which will definitely cause ignition switch failure. Individual wafer replacement, or a thorough cleaning, will make a complete replacement unnecessary.

The switch may be overheating. Is your ignition switch hot to the touch? Then there could be a short, which means the problem is in your electrical system. Because the ignition switch is connected to high-resistance wires, any of the terminals where the wires connect might overheat, and may even melt the insulating base. If this happens, your car will jerk violently and will not start.

Did you insert the wrong key in the ignition switch by accident? If you mistakenly put the incorrect key into the ignition, don’t try to get it out! You could do irreparable damage. Instead, call an automotive locksmith.

Is a broken-off key or maybe another minute object, lodged inside the lock mechanism? Don’t attempt repair yourself, because unless you know what you’re doing, you could cause irreparable damage that will cost you more. The broken key, or whatever the tiny obstacle is, can be properly removed by an automotive locksmith, and you shouldn’t have to replace the entire ignition switch.

Has a car thief attempted to steal your automobile? A bungled vehicle theft can wreck havoc on your ignition switch and on the steering column. If you’ve had this misfortune, the whole ignition assembly will have to be replaced.

The key has simply suffered too much wear and tear. As time passes, the car key grows less and less effective, and can eventually stop working. If so, it needs to be remade, applying the factory key cutting codes for accurate cutting and complete functionality.

Inspect the Ignition Status

One sure sign of a bad ignition switch is that the instrument panel won’t light up when your key is in the second position. When you insert the car key into the ignition switch and turn it, there are three basic status positions:

1.    The “off” status position: No power is transmitted to the system.

2.    The “on” status position: The dashboard lights illuminate, but the engine is still off.

3.    The “start” position: You’re placing full pressure on the key, and your engine fires up.

Check the dashboard. Regular wear and tear will lead to ignition switch failure eventually, particularly on an older car. If your ignition switch shows signs of failing, you may not hear clicks from the main relay. If you stall out, look at the dashboard lights. When you turn the key to the “on” status position, if the oil light, charge light, brake light, and other warning lights don’t turn on, then, for sure, something’s wrong.

Verify the ignition switch’s integrity. Put your key in the “start” status position. The moment you know it’s starting up, let go of the key, permitting it to snap back to the “on” status position. If the warning lights turn off when the switch snaps back, the switch is broken. You need to contact an automotive locksmith.


If you possess some automotive expertise, then you might be capable of servicing the ignition switch yourself. Be sure you know what you’re up against, because replacing an ignition switch isn’t easy, especially on newer cars, because they commonly have anti-theft devices. You’ll render your automobile inoperable if you replace the ignition switch without utilizing the correct tools, and not taking the proper precautions! Believe it or not, the electrical current running through your vehicle’s system can cause bodily harm, so keep away all metallic objects from all the electrical wires. Before installing a new ignition switch, the process includes removing the steering column, disconnecting the battery cable from the battery terminal, removing the wiring harness connected to the ignition switch, and so on. If you harbor any doubts, let an automotive locksmith take care of it instead.

Hire an Automotive Locksmith Technician

Most of the time, it’s really better to call a reputable professional. If you are located anywhere in Aurora, Colorado, choose a trustworthy automotive locksmith mobile specialist on staff at Aurora Master Locksmith, where free consultations are available.


Aurora Master Locksmith: Lock Maintenance

Regularly maintaining your locks will ensure everything is working correctly. Whether you own a home or a business, keeping your security in check is important – after all, nobody wants to have to experience the aftermath of a break-in, nor will they want to be locked out because of a malfunctioning fixture that wasn’t cared for accordingly.

For these reasons, we’re taking the time to tell you some of the basic lock maintenance checks you can do yourself – and a how a locksmith can help you enhance your overall security.

1)    For keyless entry systems: Only use brand-name batteries
You might think you’re saving money by purchasing off-brand batteries but, in the long term, that’s not true at all. Cheaper batteries have a shorter life span, so you’ll have to replace them more often, while brand-name batteries are designed to go the extra mile. In other words, invest in a good branded battery to save you the hassle of changing these more frequently.

2)    For your standard locks: Don’t close the door by tugging the key
Basically, the higher the stress on your locks, the faster its insides will become worn out. One of the simplest ways to avoid this is to ensure the lock is used only for its main function – to latch or release the door. Don’t open or close a door by tugging at the key, and try not to use heavy keyrings with multiple chains and fobs (that alone can cause a bit of unnecessary stress too).

3)    Check that everything is fitted correctly
Did you know that a badly fitted door can affect your locking mechanisms? A hanging or sagging door can weigh the locks down, which could easily cause them to backfire on you. With that in mind, check that the door is properly hung – it shouldn’t bind or sag, and the gap between the door and its frame should be even on all sides. Make sure to look at the hinges, too: ideally, you should be able to see 3-inch screws fitted onto them (these will prevent sagging as well as making your door much more resistant).
4)    Inspect your deadbolts and dead latches
Every property owner who has deadbolts installed will know that these are an invaluable protective feature. In order for these to do their job, though, you need to ensure that the hole in the door jamb is large enough to accommodate them. Deadbolts need to be fully extended to be activated – if you need to push, pull or lift the door to get them in the right position, you might need to get these refitted.
For those unfamiliar with dead latches, these are the small plungers on a door’s flattest side. Make sure these line up with the strike plate as you close the door. The dead latch shouldn’t fall into the strike plate itself, as this will lead to a lock malfunction.

5)    Look for signs of wear and tear
This tends to be the most common reason for needing to have some locks replaced. Over time, your security mechanisms are likely to become worn and torn due to stress and aging. If you fail to replace your lock in a timely manner, you’re likely to get locked out of your home or commercial building. If your key is sticking to the lock, or your locks aren’t operating as smoothly as they used to, ask your local lock and key expert to inspect your components for you.

6)    Make sure your locks are lubricated
An important part of maintenance that is regularly overlooked by all property owners. You should be oiling up your locks yearly, with Teflon-based grease or any other dry lubricant option you can find. Graphite lubricants can be a good option as well, and we strongly advise against using petroleum-based products for this task. Spray a small amount of grease into the keyway, and run the key in and out of the lock to spread it around. As you remove the key from the lock, clean up any debris before inserting it back in.

What if you need someone to inspect, repair or replace your locks? 

As we mentioned previously, neglected lock malfunctions can cause some unnecessary headaches. Getting the help that you need, as soon as you need it, is simple enough: Just in get in touch with a locally-based locksmith who specializes in the repairs you’re looking for. Most lock and key services providers offer an array of reasonably priced solutions, and would be more than happy to inspect your security components as needed. Locally-based experts will not charge you extra for travel expenses, will likely be able to provide you with after-hours assistance if you do end up locked out of your property, and will promptly assist whenever anyone needs some urgent repairs after a break-in. 

Ask around for recommendations, and select 2-3 businesses to talk to. Remember, not all locksmiths are created equal, so check if the ones you are talking to offer residential and/or commercial solutions. Other things to keep in mind when hiring a credible expert include:

–    To really get a good feeling of a business’s reputation, read up on online reviews (Angie’s List is a good place to start) and ask the locksmith for a list client references in the area.
–    Never hire a locksmith without verifiable contact details, including an address, phone number and full company name. If needed, cross-examine the business through the Better Business Bureau to see if any complaints have been set against them.
–    Always get a full price quote for repairs, and be wary of a locksmith that changes their cost estimate on the day of the repairs.
–    While partial deposits are a legitimate procedure, full payment upfront isn’t. On that note, also be on guard if a locksmith asks for cash payments.
–    Most locksmiths won’t charge for initial consultations and price quotes – so make sure to talk to an expert, inquire about their services closely, and only hire someone you are feeling truly confident about. Don’t forget to check up on license and insurance information too.  

Aurora Master Locksmith is always available to help everyone in Aurora, CO who needs to take care of their property’s locks. Simply consult with one of our licensed and insured professionals, either in person or over the phone, and we’ll help you find the right solutions for your lock issues. If you live elsewhere, you can expect your local locksmith to provide you with great value for money too!

Practical Information When You Are Locked Out of your Car

It is hard for some people to even think about being locked out of their car because it has never happened to them. If you’re having a problem remembering where you left your car keys or you suspect that they have been stolen, this article is for you. At Aurora Master Locksmith in Aurora, CO, the majority of our service requests are for motorists who are unable to locate their car keys. It is up to us to come to their aid by quickly arriving to their location in order to provide them with another key or get them back inside of their car, where they have left the key in their car ignition. If you have ever shown up to put the key in your door to get inside and realized that you do not have your keys, you already understand how upsetting such a situation can be. This is why you should heed the advice of some of the most responsive and efficient locksmiths in the area. They have seen enough people with this problem that they feel as though they can help them avoid losing their keys or what they can do if their keys are stolen. Listen up!

Trace Your Steps – If you have just discovered that you do not have your keys, you’ll need to retrace your steps to see if they show up. In some cases, you may simply put them down to pick something else up. Don’t be afraid to ask people whom you may have also come in contact with, whether or not they have noticed some keys or turned in some keys. They may just have turned them in to someone but you might never know if you do not ask.

Place Information Tags on Your Car Keys –  Some of you may think this is a little childish but this is a great way to get your keys back if they are ever lost. The only information that you’ll need to place on the tag is your contact information. Your aim is that the person who finds your keys is able to contact you to let you know they have your keys and to return them. Never put your address on your tag. This is for obvious reasons. You wouldn’t want the person who has the keys to come to your home and steal your car. The only thing that should be on the tag is your name and telephone number or email address. It is likely that if someone finds your keys, they will want to return them because they would want someone to do the same for them.

Make Sure You Have a Spare Key –  If you do not have a spare key for your car, you could be setting yourself up for a huge disappointment if you ever lose or misplace your car keys. When you have another key, it minimizes the level of frustration and anxiety that you might experience. Have a spare key made and make sure that the key or keys are given to those whom you can rely on to get them to you when you need them. You wouldn’t want to put them in the hands of someone who is often out of town or nowhere to be found. Have a spare key made immediately if you do not already have one.

Look In All the Unusual Places – Some of the most unusual places that people have found their keys are in the freezer, refrigerator, bathroom cabinet, oven and microwave. You feel might feel silly even considering the idea that your key could actually be in any of these places. However, unfortunately it is true. This is where many people tend to find their keys, especially when they have other things on their mind. They do it, without realizing it, of course. This is why it is a good idea to look in all of the most unusual places. You’ll likely find out that this is where your keys are.

Creating a Habit – In order to make sure your keys are not locked in the car, we suggest that you create a habit. This should be something that you do every time you are about to exit your car to ensure your keys are in your hand or in your purse or bag. Some people visually look at their ignition to make sure their key isn’t there. Still others will toss their keys up in the air before placing them in their purse or pocket. If you are creating a habit, you will probably feel strange the moment you do not do whatever it is that you do before you get out of your car and you’ll stop to think about what it is.

Be More Cautious During the Holidays – At Aurora Master Locksmith, we receive service requests from motorists who have locked their keys in their car or cannot find their keys. This happens a lot around the holidays. People are preoccupied and moving around quite quickly. It is easy for them to misplace or lose their keys when they have a lot to do. You can avoid losing your keys by heeding some of our suggestions above. It is advisable to recollect the above information during this time of the year. It can’t hurt to refresh your memory from time to time.

We know that it is possible for you to avoid misplacing your keys or locking them in the car with some forethought. When you slow down to heed the suggestions above, we are sure that you’ll be successful in keeping up with your car keys. You should never feel silly if you happen to lock your keys in your car because it happens to someone every day. Just make sure you remember to contact the responsive team of professional locksmiths in Aurora, CO by turning to Aurora Master Locksmith. We respond to your requests any time of the day or night.


Transponder keys are responsible for a dramatic drop in auto theft everywhere they are used. Surprisingly, many people aren’t quite sure what a transponder key really is, or they have some vague idea, but are not quite sure how they actually work. Even less known is that once in a while transponder keys can have problems, and not work as they should. This is why our Aurora Master Locksmith experts have made this post; hopefully, it will help you understand the value of your transponder keys and how to deal with any issues that may arise with them.

Let’s start with the basics!

Transponder is a word that means “to transmit” and this is exactly what your transponder key does; transmit a signal. This signal is sent from your key directly to your car’s computer. If that signal is recognized, your car starts. If not, it won’t. Can you see how this can drastically reduce car theft? The transponder key system works and works well. In fact, it’s been in use since the early 1990’s and with no signs of slowing down due to its effectiveness. You might be wondering what happens if someone makes a copy of your transponder key; won’t it make your car start for them, too? Here’s where the proverbial “catch” is. Transponder keys are hard to duplicate and program. This process is also very expensive and usually only done by car dealerships with auto maker authorization. Needless to say, these dealers will not make key copies for just anyone; you actually have be the designated owner of the car first! So what does a locksmith have to do with any of this? Keep reading; we are getting to that!

How they work

Transponder keys work the same no matter what make or model of vehicle you drive. You can be here in Aurora, CO or in Denmark, the process is uniform. The transponder key has a metal blade with grooves and niches cut into it, much like a regular key. It also has a rounded or rectangular head to be used for turning. The difference is that your transponder key also has a programmable chip embedded in the key head. This chip is what sends the signal to your car’s computer. Let’s put this all together now. In order for your chip to send any signal at all, it must first be embedded in your key AND also programmed to match your vehicle’s computer. This process is where the expertise and expense come into play, making it harder for thieves to make a quick copy and then drive off in your car.

They sound wonderful, but…

You may be thinking, “So what’s the problem?” We are coming to that! Transponder keys can break, become lost, get stuck, lose their chip, become worn; you name it! Whether you are here in Aurora, CO or elsewhere, it pays to know what to do in any of these events. Like anything else, knowledge is power so keep reading to see how best to deal with transponder key problems if they happen to you!

Stuck transponder key

Car keys get stuck; that’s a fact of life. This of course includes transponder keys. The make or model does not matter; a Mercedes coupe key can stick as easily as one from a Kia sedan. Just remember to remain calm when it happens. It’s hard to; after all, your key is stuck so how are you going to lock the door or open your trunk? It’s important to not try and force your key to come out. You run the danger of key breakage by doing this. Simply jiggle the steering wheel back and forth a few times and see if this releases it. You can also check your gear and see if you are in the PARK position. You can’t be almost in PARK, you must be IN the right gear or sometimes the ignition locks up and holds your key in the process. It is actually a safety factor so that your key doesn’t come out while you are zipping down the freeway, so this feature is there for your own good.

Transponder key breakage

Just because they have a computer chip inside of them doesn’t mean that you have a SUPER KEY that never breaks, or becomes damaged. Here at our Aurora, CO lock shop we often hear about keys being used to open bottles, cans and boxes just because they have a handle to hold and a metallic, bladed point that can be used to cut, puncture or slash! Keys should be used for just that and not as a Boy Scout tool that can “do it all.” You can’t always avoid key breakage but you can cut down on its rate of occurrence by taking better care of the ones you have.

Where’s my chip?

Your transponder chip can indeed fall out. Usually, this happens when the key is dropped or thrown about forcefully. It can be hard to notice that your tiny transponder chip is now lying on the ground unless you are specifically looking for it. Instead, most people simply bend over and pick up their dropped keys and go about their business. By the time they notice that the car won’t start, it’s too late and either they can’t remember where they dropped the key, or the chip is now long gone. Please not that a transponder key without the computer chip can still open car doors and the trunk; it just can’t start the ignition.

Lost transponder keys

If you lose things easily, it may be time to acquire a new habit; putting items in the right place each time you use them. Instead of just tossing your car keys on the table or dresser when you come home, put them in a place designated just for them. It might be on a hook, in a drawer, or in a small container on your night stand. Do this enough times and you’ll always know just where your transponder keys are at the moment.


It happens to the best of us. It’s so aggravating and inconvenient to see that you are locked out, and it’s particularly infuriating if you’re stranded without your keys after sundown. Right now, you can decide to put some simple principles in place as a daily habit. Choose to adopt these easy strategies from now on, and there will be no reason you’ll ever find yourself locked out again!
Store a spare key in a common-sense hiding place. Putting a key under the mat, beneath a flower pot, or over your door frame, is not a good idea. Every thief knows to look in these places. A fake-rock keyholder is pointless if a professional criminal already knows what it looks like. It’s better to give your extra key to a neighbor you trust ~ preferably someone who’s home most of the time.
Keys, wallet, phone.Whenever you go out the door, remind yourself: keys, wallet, phone. Make it your basic mantra from now on. Stop. Do a pat-down, check your pockets, and check your purse or pack. (You might want to add a few more items to your list, such as: driving glasses, reading glasses, sunglasses, and so on.)
Replace any faulty locks. Keep an eye on all your locks. Upgrade, fix, or replace them when needed. If any of your locks become hard to open, the key could break inside the lock mechanism. Don’t get copies of keys made that are already duplicates, because they eventually won’t work. If you have any locks that are too worn-out, they’re bound to get jammed.
Always know where your keys are. Stay aware of your keys wherever you go. If you walk out, and you realize that you’ve forgotten something, and then you go back to get it, don’t put your keys down on the table and forget them! Keep your keys in your hand, or inside your pocket or purse. Remember, if you ever lend a spare key to a trusted friend, always get it back as soon as you can.
If you want to be bold, carry a phony credit card. Keep one of those fake sample credit cards from junk mail, or an expired gift card. Don’t use an actual one, because you will definitely ruin it. It doesn’t work like it does in the movies, but it still might work for you ~ that is, only if there isn’t a deadbolt. It must be a bored door lock, with the sloped ridge of the bolt facing toward you. (If the door opens toward you, then the bolt is probably facing the wrong way.) If the bolt is the right type, and it’s facing the right direction, then give it a try:
1.      Put the card in the space in between the door and the jamb above the bolt.
2.      Ever so gently, slide the card down between the strike plate and the bolt.
3.      Push the card, and push the door.
4.            If you are fortunate, the door will open, and you’ll leave everything (except the card) undamaged.
If you’re more adventurous, take a pick set with you. If your local and state laws allow you to do so, try picking the lock. Not all locks can be picked, but it could be worth a try. And perhaps some day you will be able to help someone else who’s locked out.
Before you get into a jam, find a legitimate locksmith. The right way to locate a reputable locksmith is to track one down ahead of time, beforeyou ever need one. Do your research, so you won’t get scammed or overcharged.
Ask family, friends, and colleagues for recommendations. Word of mouth from a satisfied customer is always your best bet.
Do your homework. To find a local trusty locksmith, check your phone book and the Web. Write down locksmith companies in your area, with their addresses and telephone numbers. Locate the locksmiths who specialize in the services you need. Utilizing the Internet, you can match up the telephone numbers with the street addresses. A deceptive company may list a fake address, or none at all, claiming it’s local. If someone answers your call with a general greeting such as “locksmith services,” then ask for what the whole business name is. If that person won’t tell you, take it off the list. Bear in mind that some reputable locksmith companies might not include a street address simply because they run a mobile business, so that they can dispatch a locksmith professional local to every customer. Therefore, just ask why their address isn’t listed.
Confirm the locksmith’s credentials. When the locksmith arrives, ask for ID, a business card, and proof of license. The invoice ought to include the locksmith company’s name. The locksmith’s truck should show the company name as well, and match the company name on the business card and invoice. The locksmith must also ask you for your identification, too. Before beginning any work, a locksmith must authenticate your identity, and verify that you’re the actual property owner.
Be skeptical if a locksmith tells you you’re going to have to drill or replace your lock just because you’re locked out. An expert locksmith of integrity will carry the right tools, and have the expertise to know that such drastic measures would be overkill. A true professional locksmith is able to unlock virtually anything.
When you’ve finally found a reliable locksmith, keep that company’s contact information in a logical place, such as on your smart device, on the refrigerator, in your wallet, or on your bulletin board at work ~ so you’ll always have what you need to get yourself out of trouble . An exceptional locksmith will always be happy to answer your questions.
If you’re in Aurora, Colorado, consider hiring Aurora Master Locksmith, a locksmith company whose staff mobile professional locksmith technicians are available 24/7 to provide automotive, residential, commercial, and emergency locksmith solutions.
What if you’re locked out now? If you don’t have a hidden extra key, or you don’t have a neighbor or friend who keeps one for you, then check to see if you left a window or another door open.

If all else fails, hire a locksmith! You may be tempted to entertain the idea of kicking in the door or breaking a window. But should you really risk being mistaken for a burglar? Of course not. Avoid this mess in the future! Plan ahead!

Aurora Master Locksmith: What to Do When a Safe Is Jammed

Whether you’re a homeowner or business owner, a safe is always a great choice for protecting your valuables. While you can trust these to provide you durable security, there’s always the odd occasion when you might be faced with a safe that’s no longer opening as it should. A locksmith will be able to help you with these issues, but there are some quick checks you can do yourself before calling for assistance. If you find yourself with a safe that is jammed, here is what you need to do:

Possible reasons your safe won’t open

1)    Dead batteries
The best case scenario for all safe troubles is that the culprit is simply a dead battery. Even if you see lights shining through your keypad, it’s always best to test the batteries – before applying any other fixes, as a low-power surge may impede it to complete its opening operations. See if a battery change resolves your issues. But take note: off-brand batteries wear out much quicker than branded ones, so it’s best to invest in a battery that will have a longer lifespan.

2)    Your bolt work is stuck
If you can hear a motor running but you can’t open your safe, the most likely reason for it will be that the bolt work is jammed. The first thing you need to do in order to get it unstuck? Kick it. Yes, you read that correctly – turn your back to the safe, and mule kick the door a couple of times. Be very careful not to hit the keypad or handle: you’re trying to loosen the bolt work, not damage the safe’s components. After doing this a few times, try and turn the handle in the opposite direction it’s supposed to go, and enter your safe’s combination. All these steps should release the pressure from the bolt work, allowing you to move it more freely.

3)    Deactivated code
When you have a safe with multiple combinations, a code deactivation could explain why your safe is not opening. In this situation, get someone else who has access to the safe through a different code to check if they can open it. If their code works without a hitch, you may need to set up a new combination for yourself.

4)    Penalty lockout modes and/or time delay
Many safes will penalize you for entering the wrong digits too many times. This can come in the form of a time delay, where you have to wait a few minutes before you try again, or a full lockout mode. You’ll know when you’re faced with the latter as it often comes with a loud beeping noise. In both cases, wait about 10 or 20 minutes, and try opening it again.

5)    Damaged wiring
Your safe’s keypads, like any other electronics, are not fully immune to damaged or faulty wiring. If you’re confident about your DIY abilities, remove the keypad from the door and inspect the wiring to see if anything has come loose, snapped, or there are any kinks causing an interference. Everything looks intact? Then try disconnecting the battery for 20 seconds, reinstalling it again, and connecting everything back together to check if it’s all back to normal. Seeing strong signs of damage? You’ll need to call a locksmith – make sure to tell them what type of safe and keypad you own so they can come with the right parts for your replacement.

6)    Shifting numbers
This is something that occurs in safes with older combination locks or locks that haven’t been properly maintained, where the code would have shifted positions. Combination shifting is a sign that you’ll need to call a professional, as these tend to indicate that, without proper repairs, the lock will fail completely.

The way to check for combination shifting is to either subtract one from each number, and keep trying this until you’ve subtracted five, or to proceed with the same steps but adding to the numbers instead. In other words, if you have a safe combination of 50-60-70, you would initially try 49-59-69, then 48-58-68 and so on until you’ve reached 45-55-65; and then you would do the same with addition: from 51-61-71; 52-62-72 right until 55-65-75. 

Getting help from a qualified locksmith 

A qualified locksmith will be well-versed in safe installations, repairs and replacements. If you’re experiencing any kind of issues with your home or business safe, these pros should be your port of call – they will have all the right equipment to solve your issues promptly and efficiently. Remember to always hire a locally-based expert who specializes in the type of protection you are looking for – some locksmiths may only focus on residential services, for instance, while others may offer a fully-inclusive set of options.

When choosing the right professional to hire, it’s always best to get recommendations and take the time to do some background checking. Local lock and key services providers won’t balk at you for requesting information like license and insurance details, how long they’ve been in business, and a list of client references in your area. Reading up on online reviews and cross-checking each company through your local Better Business Bureau will also help you get better insight into the locksmith business’s reputation.

Always get a full cost breakdown for your safe repairs, and be very wary of any locksmith who changes their price quote upon arriving to your property. Whenever possible, try to visit a company on their location and consult with a professional about their solutions. Never hire a business you can’t trace a physical address back to, and be very wary of any locksmith who changes their price quote on arrival and tries to get you to agree to a full safe replacement without a valid reason.
Are you looking for safe repairs in and replacements in Aurora, CO? The licensed and insured team at Aurora Master Locksmith will be able to help. We’re available 24/7 in case of emergencies, and you can always get a free consultation and price quote from our locally-based business too.

No matter where you live, a locally-based locksmith will help you resolve any issues that emerge from a jammed up safe. Whether you need to replace a keypad, or you simply need to change the combination, a qualified expert will bring you full peace of mind in all situations.  

Finding the Right Locks for Home and Business

With the amount of different locks that there are so choose from, you might find it difficult to find the right lock for your needs. If you live in or around Aurora, CO, you can count on the expert locksmiths of Aurora Master Locksmith to provide you with the help that you need in determining which type of lock to have installed. We would advise you to take some time to at least read about the different types of locks that you can choose from before you decide on a particular type. While we encourage you to do your research, we know that it can be rather time consuming when you have absolutely no idea what is available to you. We have simplified this process for you by highlighting some of the most popular types of home and business locks used today. You might already have lever, deadbolt, knob or padlock lock on your doors but not know how they work. Read below for additional information.

Deadbolt Locks

You’ll be able to choose between three types of deadbolt locks. There is a single, double or thumb turn deadbolt lock. It is the single cylinder lock that you will found installed in most homes. A key cylinder is used on the outside of the door with the thumb turn inside. This is what helps you open the door. You will be required to have a key in order to open either side of the door. This could be problematic if there is an emergency and you need to make a quick exit. The problem would result when you are unable to locate one of the keys. A thumb turn lock has both the single and double cylinder. This type of deadbolt lock can be locked with the use of a key.

Rim Locks/Mortise Locks

This type of lock is usually used on doors of commercial businesses or apartments. The two locks are similar in some regards but they use different hardware. A rim cylinder lock is installed on the inside of a door. There is a long piece that shoots out the back of the lock and connects to the locking mechanism on the other side. The mortise lock uses hardware on the inside. A cam is used to connect the locking mechanism and is kept together with a set of screws. Mortise locks come in different lengths and cams, based on the type of hardware the lock has.


A padlock is made of strong, sturdy materials but is not a permanent lock. This type of lock can be removed and placed on other things, as needed. There are keyed padlocks and combination padlocks. With a combination padlock, you are required to enter a specific set of numbers in order to disengage the lock. They come in rekeyable and non-rekeyable. This means that with the rekeyable lock, it can be changed but the none-rekeyable lock will not enable you to do this (change the lock).
Knob Locks

This is what you’ll find on most home locks. They shouldn’t be used as your main lock. The lock cylinder is not on the inside of the door rather it is inside the knob. This makes it easy to break. While you see this type of lock on the outside of many homes, at Aurora Master Locksmith we suggest you have this type of lock installed on the inside doors of your home. We also recommend that when it is used on your home that there is also a deadbolt lock on the same door.
Wall Mounted Lock

Used for most commercial businesses, a wall mounted lock can be used for storing small items, such as, keys. This type of lock is often installed during the building process. Some even have alarm sensors, which alert you to unauthorized entry.

Interchangeable Core Cylinder Lock

Large businesses have this type of lock installed and is known for their convenience. Re-keying is possible without taking the whole key apart. We only need to change the core to change the lock. Two keys open this type of lock a control key and traditional key. It is also convenient because you don’t have to change the hardware to change the lock. Unlike most other locks, you cannot install a deadbolt lock alongside an interchangeable core cylinder. They simply do not work together.

Lever Handle Lock

We install this type of lock on the inside of a lot of commercial businesses. They give customers or clients easy and convenient access by just pushing down on the handle and opening the door. 

Jimmy Proof Deadbolts

This is a lock that is installed on apartment doors. It cannot be modified too much. It isn’t easy to break this type of lock because it connects to the jamb bracket. While it isn’t easy to break, it is simple to have installed. It is screwed to the inside of your door. A hole is made to install the rim cylinder. 

Rim Latch Locks

There is a surface mount latch on one side with a rim cylinder on the other. You’ll also find this type of lock in apartments. This isn’t the type of lock that you’ll want to use as your primary lock without using something like a deadbolt along with it.

Don’t take this decision lightly. Let a qualified and experience locksmith help you make your final decision about the type of locks to have installed. It is possible to find a key in your price range that is durable enough to withstand the attempt of a break in. Let a locksmith technician know what you’re looking for in terms of the type of lock that would be best for you and your family. If you need convenience, let the locksmith know that is what is most important to you. If you need locks that can be easily re-keyed, they can steer you in the right direction. You only have to ask and they will be happy to help.